![does waves v9 actually have all these plugins does waves v9 actually have all these plugins](https://support.image-line.com/innovaeditor/assets/Tickets/1234322--FCTPQJiPyQ.jpg)
If you work at higher sample rates but frequently run out of DSP, you may want to consider working at a lower sample rate. At 4x sample rates (176.4 / 192kHz) the idle DSP usage of an Apollo interface with no UAD plug-ins loaded will decrease, but that is a side effect of certain features such as Aux channels and Flex Routing being disabled automatically for technical reasons. Keep in mind that UAD plug-ins require more DSP when working at higher sample rates. Optimizing the Console > Settings > Hardware panel If you are using an Apollo Twin and are not using the ADAT inputs, you can head to Console > Settings > Hardware panel > Options, and switch the "DIGITAL INPUT" mode to SPDIF from ADAT to conserve some additional DSP. If you don't meet BOTH of those conditions, you can safely set IDC to OFF to save some DSP. Any of those input channels contain upsampled UAD plug-ins. Multiple Console inputs are used for a single source (such as a drum kit using multiple microphones).Ģ. Keeping this setting at the minimum (2) will conserve a few % points of DSP.Īnother feature we can consider is "INPUT DELAY COMPENSATION" (IDC). Console IDC is required to maintain phase alignment only when BOTH of the following conditions are active:ġ. If you own an Apollo 8, 8p, 16, or 16 mkII, the first thing we can do is minimize the "CUE BUS COUNT" if you don't need all 4 independent cue sends.
![does waves v9 actually have all these plugins does waves v9 actually have all these plugins](https://i.imgur.com/clm9Zt2.jpg)
We will achieve this by turning some features off, but you should only do this if you don't need to use those particular features. If you own an Apollo audio interface, you can head to Console > Settings > Hardware panel to adjust some settings to further conserve on DSP. The same concepts apply to Console 1, although the location of certain settings may be different. Note: These directions address settings in Console 2. Optimizing Console Settings (Apollo interfaces only)
Does waves v9 actually have all these plugins pro#
Next, under "HOST COMPATIBILITY", check the box next to "Release all UAD DSP resources on AU bypass." If you use Logic Pro X or another Audio Units compatible host, this will ensure that bypassing a UAD plug-in will actually release the DSP it uses in realtime.Ĭonfiguring The UAD Meter & Control Panel for optimum DSP usage For example - with DSP LoadLock disabled, the EQ section of the Neve 1073 Preamp and EQ Plug-in can be disabled to save a considerable amount of DSP. If DSP conservation is the goal we can uncheck this option to potentially save on processing power when particular features or modules of certain plug-ins are not in use. Next, you can uncheck the box next to "DSP LoadLock." This feature reserves the maximum amount of DSP that a UAD plug-in could potentially use regardless of whether you have actually enabled all of the features or modules of that plug-in. This is the default setting that we recommend for most systems. On the Configuration tab of the UAD Control Panel under the "UAD-2 DSP" section, make sure that "Limit DSP load to" is set to the maximum value (100%). There are a handful of settings we can adjust in the UAD Meter & Control Panel that will affect the performance of all of our device categories (PCIe cards, Satellites, and Apollo interfaces). Optimizing the UAD Meter & Control Panel (all devices) Note: UAD-2 Satellites and PCIe cards cannot be used to process UAD plug-ins in Apollo's Console. In the short term, however, there are a few strategies you can use to squeeze the most DSP power out of your existing setup as possible. We've all been there before - you're almost done with the final mix of your latest session and you reach for one last UAD plug-in to seal the deal, but alas - no more DSP is available! In the long run, this may be a good indication that another Apollo, Satellite, or PCIe card would be a good addition to your setup to maximize the number of simultaneous UAD plug-ins you can use.